Pixhawk 6X-RT Dev Edition Autopilot Compatible W/Pixhawk & RPi CM4 Baseboards RC
$ 251.59
Description
Pixhawk 6X-RT Dev Edition Autopilot Compatible W/Pixhawk & RPi CM4 Baseboards RC. The Pixhawk 6X-RT is based on the Pixhawk® FMUv6X-RT Open Standard and the Pixhawk® Autopilot Bus Standard. Pixhawk Standard Baseboard v2A/Pixhawk Standard Baseboard v2B/Pixhawk Standard Baseboard v1. Overview The Pixhawk 6X-RT is based on the Pixhawk® FMUv6X-RT Open Standard and the Pixhawk® Autopilot Bus Standard. It comes with PX4 Autopilot® pre-installed. Inside the Pixhawk 6X-RT flight controller, you can find an NXP-based i.MXRT1176 MCU, paired with sensor technology from Bosch® and InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle. The i.MXRT1176 microcontroller contains an Arm® Cortex-M7 at 1 GHz and a Cortex-M4 at 400 MHz. It has 2MB SRAM and 64MB Octal SPI Flash. Thanks to the updated processing power, developers can be more productive and efficient with their development work, allowing for complex algorithms and models. It includes high-performance, low-noise IMUs designed for better stabilization, and has triple redundant IMUs & double redundant barometers on separate buses. When the Autopilot detects a sensor failure, the system seamlessly switches to another to maintain flight control reliability. An independent LDO powers every sensor set with independent power control. A vibration isolation system to filter out high-frequency vibration and reduce noise to ensure accurate readings, allowing vehicles to reach better overall flight performances. An integrated Microchip Ethernet PHY, high-speed communication with mission computers via Ethernet is now possible. The Pixhawk 6X-RT is perfect for developers at corporate research labs, startups, academics (research, professors, students), and commercial application. This Flight controller is compatible with any baseboard that uses the Pixhawk Autopilot bus, such as the Pixhawk Baseboard , Pixhawk Mini Baseboard , and Pixhawk RPi CM4 Baseboard . Key Design Points High performance dual core i.MXRT1176 Processor with Cortex-M7 @ 1GHz – Cortex-M4 @ 400MHz Modular flight controller: separated IMU, FMU, and Base system connected by a 100-pin & a 50-pin Pixhawk® Autopilot Bus connector. Redundancy: 3x IMU sensors & 2x Barometer sensors on separate buses Triple redundancy domains: Completely isolated sensor domains with separate buses and separate power control Vibration isolation system to filter out high frequency vibration and reduce noise to ensure accurate readings Ethernet interface for high-speed mission computer integration IMUs are temperature-controlled by onboard heating resistors, allowing optimum working temperature of IMUs Hardware secure element NXP EdgeLock SE051an extension to the widely trustedEdgeLock SE050 Plug & Trust secure element family , supports applet updates in the field and delivers proven security certified to CC EAL 6+, with AVAVAN.5 up to the OS level, for strong protection against the most recent attack scenarios.. E.g to securely store operator ID Note: This developer edition for early adopters while we continue to accumulate flight test hours This Flight Controller is currently support in PX4 Flight Stack only. (Firmware Target: FMUv6xrt ). It is not supported in Ardupilot. This Flight controller uses digital power module (same as Pixhawk 6X, full list can be found here ) Power module comparison chart Specification MCU: i.MXRT1176 Cortex-M7 @ 1GHz Cortex-M4 @ 400MHz 2MB SRAM 64MB Octal SPI Flash IO Processor: STM32F103 32 Bit Arm® Cortex®-M3, 72MHz, 64KB SRAM On-board sensors Accel/Gyro: BMI088 Accel/Gyro: ICM-42670-P Accel/Gyro: ICM-42686-P Mag: BMM150 Barometer: 2x BMP388 Hardware secure element NXP EdgeLock SE051C2 SDHC interface 12-Channel PWM 8x UART 4x I2C 6x SPI 3x CAN-FD RMII 100M Ethernet USB Open-Source Software enablement PX4 Autopilot NuttX RTOS Zephyr RTOS SKU11064 Includes: Pixhawk 6X-RT Flight Controller Module SKU20298/20319/20257 Includes: Pixhawk 6X-RT Flight Controller Module Pixhawk Standard Baseboard v2A/Pixhawk Standard Baseboard v2B/Pixhawk Standard Baseboard v1 PM02D HV Power Module Cable Set Reference link: Firmware Flashing Instruction (Github) PX4 on the NXP IMXRT1176 1 GHz MCU - Presentation slides by NXP i.MX RT1176 – product page 1 GHz Crossover MCU with Arm® Cortex® Cores EdgeLock® SE051 : Proven, Easy-to-Use IoT Security Solution with Support for Updatability and Custom Applets
![Traxxas Screws 2.6x5mm Button-Head Machine (6) Aton [TRA7944]🌟✨25 Years on eBay! 250,000+ feedback!✨🌟](/?s=images_g_eiEAAeSwBf9pwWRr_s-l1000.jpg)
![Tamiya Frog Differential Bevel Gears Set [TAM9440510]🌟✨25 Years on eBay! 250,000+ feedback!✨🌟](/?s=images_g_fioAAeSw5JVpwdWP_s-l1000.jpg)
